KIT INCLUDES:
HARDWARE REQUIRED
SOFTWARE REQUIRED
Arduino IDE 1.8.5 (programmable platform for Arduino)
Click To Download :https://www.arduino.cc/en/Main/Software
SPECIFICATIONS
DS3231 RTC MODULE
| Operating Voltage |
3.3 V-5.5 V DC |
| Chip |
DS3231 |
| Pin no. |
6 |
| Operating Temperature Ranges |
Commercial: 0°C to +70°C |
| Industrial: -40°C to +85°C |
| Power Consumption |
Low |
| Accuracy ±2ppm |
0°C to +40°C |
| Accuracy ±3.5ppm |
-40°C to +85°C |
| I2C Interface |
Fast (400KHZ) |
| Digital Temp Sensor Output |
±3°C Accuracy |
SD CARD MODULE
- Operating voltage 5V
- SPI Communication method
- SD card Socket
- Supports FAT16 and FAT32
- Support 2gb to 4gb
ARDUINO NANO
- Microcontroller: Atmel ATmega168 or ATmega328
- Operating Voltage(logic level): 5 V
- Input Voltage(recommended): 7-12 V
- Input Voltage(limits): 6-20 V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 8
- DC Current per I/O Pin: 40 mA
- Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader
- SRAM: 1 KB (ATmega168) or 2 KB (ATmega328)
- EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328)
- Clock Speed: 16 MHz
PIN DESCRIPTION
DS3231 RTC MODULE
.jpg)
| PIN |
NAME |
FUNCTION |
| 1 |
32KHZ |
32kHz Output. This open-drain pin requires an external pullup resistor. It may be left open if not used. |
| 2 |
VCC |
DC Power Pin for Primary Power Supply. This pin should be decoupled using a 0.1µF to 1.0µF capacitor.
If not used, connect to ground. |
|
3 |
INT/SQW |
Active-Low Interrupt or Square-Wave Output. This open-drain pin requires an external pullup resistor. It may be left open if not used. This multifunction pin is determined by the state of the INTCN bit in the Control Register (0Eh). When INTCN is set to logic 0, this pin outputs a square wave and its frequency is determined by RS2 and RS1 bits. When INTCN is set to logic 1, then a match between the timekeeping registers and either of the alarm registers activates the INT/SQW pin (if the alarm is enabled). Because the INTCN bit is set to logic 1 when power is first applied, the pin defaults to an interrupt output with alarms disabled. |
| 4 |
GND |
ground |
| 5 |
SDA |
Serial Data Input/Output. This pin is the data input/output for the I2C serial interface. This open-drain pin requires an external pullup resistor. |
| 6 |
SCL |
Serial Clock Input. This pin is the clock input for the I2C serial interface and is used to synchronize data movement on the serial interface. |
ARDUINO NANO
CIRCUIT CONNECTION
- Connect all the vcc from the battery holder to the breadboard positive and all the grounds to the negative.
- Connect the SCL pin of ds3231 to arduino Nano a5 pin, and SDA to a4.
- Connect cs pin of SD card module to D10 of arduino Nano SCK to D13,MOSI to D11,MISO to D12.
- Now connect the battery positive to + lane on breadboard and negative to negative lane of breadboard.
CODE
Click to see the code or copy the link:
https://docs.google.com/document/d/e/2PACX-1vQSSHMkDZZTdW60X-oHw9BDUR13KfJOT4TlvBTEudhleMvSI8I_MeULlFsKPRR4x_E13-SAwwHCVvdB/pub
WORKING
In this project we are going to use arduino Nano, SD card module, and DS3231 real time module. This project reads temperature in every few minutes and save the data in the SD card. The DS3231 has a temperature sensor embedded in it in with the help of arduino Nano the ds3231 RTC will record the real time and temperature and save it in the SD card which is placed in the SD card module.
Ultimate Uno R3 Kit compatible with ARDUIN0 IDE1 ×₹4,602.00
Super Starter Kit for Uno R3 compatible with Arduino IDE1 ×₹2,594.82
