KIT INCLUDES:
HARDWARE REQUIRED
SPECIFICATIONS
16*2 LCD DISPLAY
- LCD Display Mode: STN, Positive, Transflective
- Display Color: Deep Blue/ Yellow Green
- Viewing Angle: 6H
- Driving Method : 1/16 duty, 1/5 bias
- Back Light : Yellow-Green LED backlight
- Outline Dimension: 803615.8 MAX
CAUTIONS
• The LCD panel is made by glass. Any mechanical shock (eg. dropping from high place) will damage the LCD module.
• Do not add excessive force on the surface of the display, which may cause the Display color change abnormally.
• The polariser on the LCD is easily get scratched. If possible, do not remove the LCD protective film until the last step of installation.
• Never attempt to disassemble or rework the LCD module.
• Only Clean the LCD with Isopropyl Alcohol or Ethyl Alcohol. Other solvents (eg.water) may damage the LCD.
• When mounting the LCD module, make sure that it is free form twisting, warping and distortion.
• Ensure to provide enough space(with cushion) between case and LCD panel to prevent external force adding on it, or it may cause damage to the LCD or degrade the display result.
• Only hold the lCD module by its side. Never hold LCD module by add force on the heat seal ot TAB.
• Never add force to component of the LCD module. It may cause invisible damage or degrade of the reliability.
• LCD module could be easily damaged by static electricity. Be careful to maintain an optimum anti-static work environment to protect the LCD module.
• When peeling off the protective film from LCD, static charge may cause abnormal display pattern. It is normal and will resume to nomal in a short while.
• Take care and prevent get hurt by the LCD panel sharp edge.
• Never operate the LCD module exceed the absolute maximum ratings.
• Keep the signal line as short as possible to prevent noisy signal applying to LCD module.
• Never apply signal to the LCD module without power supply.
• IC chip(eg. TAB or COG) is sensitive to the light. Strong lighting environment could possibly cause malfunction. Light sealing structure casing is recommend.
• LCD module reliability may be reduced by temperature shock.
WATER FLOW SENSOR
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Liters/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Liter: 450
- Durability: minimum 300,000 cycle
SOFTWARE REQUIRED
Arduino IDE ( programmable software for Arduino boards )
You can download the software from this link :Â https://www.arduino.cc/en/Main/Software
PIN DESCRIPTION
10K POTENTIOMETER
16*2 LCD DISPLAY
WATER FLOW SENSOR
CIRCUIT DESCRIPTION
Flow sensor Yellow Wire is output and it gives pulses in proportion with flow.
Flow Sensor Connections
Yellow — Pin 2
Red — +5V
Black — GND
LCD Connections
LCD RS pin to digital pin 12
LCD Enable pin to digital pin 11
LCD D4 pin to digital pin 6
LCD D5 pin to digital pin 5
LCD D6 pin to digital pin 4
LCD D7 pin to digital pin 3
LCD R/W pin to ground
1K resistor:
One end to ground
Another end to LCD VO pin (pin 3)
CODE
click to see the code
https://docs.google.com/document/d/e/2PACX-1vQp-DYSluOk_Q_PVx5ZkdDL9RjJiDOpfbo7XQfNN5CS-92FbX_3lrSKXbf6x1Opb_DuVEgHM5OqT4Of/pub
WORKING
1. Blow air or allow water flow through the sensor
2. Observe the reading on LCD or Serial Monitor
3. Readings get updated at every 1 Sec
HERE we connect the water flow pump 12 dc motor use for flow the water between the water flow sensor you see the result on lcd 16*2
Super Starter Kit for Uno R3 compatible with Arduino IDE1 ×₹2,594.82
