KIT INCLUDES:
HARDWARE REQUIRED
SOFTWARE REQUIRED
Arduino IDE 1.8.5 (programmable platform for Arduino)
Click To Download :https://www.arduino.cc/en/Main/Software
SPECIFICATIONS
4*4 KEYPAD MEMBRANE
- Maximum Rating: 24 VDC, 30 mA
- Interface: 8-pin access to 4×4 matrix
- Operating temperature: 32 to 122 °F(0 to 50°C)
- Dimensions: Keypad, 2.7 x 3.0 in (6.9 x 7.6 cm),Cable: 0.78 x 3.5 in (2.0 x 8.8 cm)
16*2 LCD DISPLAY
- LCD Display Mode: STN, Positive, Transflective
- Display Colour: Deep Blue/ Yellow Green
- Viewing Angle: 6H
- Driving Method: 1/16 duty, 1/5 bias
- Back Light: Yellow-Green LED backlight
- Outline Dimension: 803615.8 MAX
| Note |
- Colour tone may slightly change by Temperature and Driving Condition.
- The Colour is defined as the inactive/background colour
|
PIN DESCRIPTION
16*2 LCD DISPLAY
| Symbol |
External Connection |
Function |
| VSS |
Power Supply |
Signal GROUND for lcm |
| VDD |
POWER SUPPLY for logic lcm |
| V0 |
Contrast Adjust |
| RS |
MPU |
Register Select Signal |
| RW |
MPU |
Read/Write Select Signal |
| E |
MPU |
Operation Enable Signal |
| DB0~DB3 |
MPU |
Four Low order bidirectional three state bus lines. Used for data transfer between the MPU and LCM. These four are not used between 4 Bit operations. |
| DB4~DB7 |
MPU |
Four high order bidirectional Three state bus lines used for data transfer between the MPU |
| A |
LED BKL power Supply |
Power Supply for BKL |
| K |
4*4 KEYPAD MEMBRANE
Matrix keypads use a combination of four rows and four columns to provide button states to the host device, typically a microcontroller. Underneath each key is a pushbutton, with one end connected to one row, and the other end connected to one column.
CIRCUIT CONNECTION
- Keypad 1 to arduino D0
- Keypad 2 to D1
- Keypad 3 to D2
- Keypad 4 to D3
- Keypad 5 to D4
- Keypad 6 to D5
- Keypad 7 to D6
- Keypad 8 to D7
- Lcd pic 16 to negative rail and pin 15 to positive rail
- Lcd pic D7 to D4 to arduino D13 to D10
- Arduino 5V to positive rail and ground to negative rail
- Arduino pin D8 to RS of lcd and D9 to pin 6 (E) of lcd
- Lcd pin1 to ground, pin 2 to 5v , pin 3 to ground and pin 5 to ground
CODE
Programming is always fun and Arduino is a wonderful platform if you are just getting started with Embedded programming. In this, we will build our own calculator with Arduino. The values can be sent in through a keypad (4×4 keypad) and the result can be viewed on an LCD screen (16×2 Dot-matrix). This calculator could perform simple operations like Addition, Subtraction, Multiplication and Division with whole numbers.
The complete circuit diagram of this Arduino Calculator Project is given above. The +5V and ground connection shown in the circuit diagram can be obtained from the 5V and ground pin of the Arduino. The Arduino itself can be powered from your laptop or through the DC jack using a 12V adapter or 9V battery.
We are operating the LCD in 4-bit mode with Arduino so only the last four data bits of the LCD is connected to Arduino. The Keyboard will have 8 output pins which have to be connected from pin 0 to pin 7 as shown above. You can use the following connection to verify your connection with Arduino, you can also check 4×4 Keypad interfacing with Arduino.
“Some Arduino boards might show an error while uploading program if there is anything connected to pin 0 and pin1, so if you experience any just remove the keypad while uploading the program.
As told earlier we are going to interface an LCD and keypad with Arduino using libraries. So let’s add them to our Arduino IDE first. The library for LCD is already included in your Arduino by default so we need not worry about it. For Keypad library click on the link to download it from Github. You will get a ZIP file, then add this lib to Arduino by Sketch -> Include Library -> Add.ZIP file and point the location to this downloaded file. Once done we are all set for programming.
Even though we have used a library for using a keypad we have to mention few details (shown below) about the keypad to the Arduino. The variable ROWS and COLS will tell how many rows and columns our keypad has and the key map shows the order in which the keys are present on the keyboard
https://docs.google.com/document/d/e/2PACX-1vQIVFRbugqndpyFptAOfi3jq4QcujiIwD4UtCPS06Oz3mtt1HFbl9nZ2B642U1A8jrLpjQMi-OCs0ek/pub
WORKING
- Make the connections as per circuit diagram and upload the code below. If it shows error make sure you have added the library as per the instruction is given below
Library Links:
https://www.arduino.cc/en/Reference/LiquidCrystal
https://github.com/Chris–A/Keypad
- Arduino Calculator using 4×4 Keypad in action
- Since the keypad used here does not have proper markings on it I have assumed the Alphabets to be operators as listed below.
Character on Keypad assumed to be
“D” Addition (+)
“A” Subtraction (-)
“B” Multiplication (*)
“C” Division (/)
“*” Clear (C)
“#” Equals (=)
Basic Starter Kit For Compatible With Arduino SMD UN2 ×₹2,124.00
Ultimate Uno R3 Kit compatible with ARDUIN0 IDE1 ×₹4,602.00
