-20%

Make a Pattern with 16 Leds using HC595 shift Register interfacing with Arduino Uno

Category: Arduino Compatible Kits Tags: Arduino Uno, HC595 shift Register, Pattern with 16 Leds

Description
Reviews (0)

KIT INCLUDES:

HARDWARE REQUIRED

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino)

Click To Download :https://www.arduino.cc/en/Main/Software

TYPICAL APPLICATION

HC595 SHIFT REGISTER

General Purpose Logic
Serial to Parallel Data conversion
Capture and hold data for extended periods of time.
Allow simple serial bit streams from a microcontroller to control as many peripheral lines as needed.
Wide array of products such as:
Computer peripheralS
Appliances
Industrial control

SPECIFICATIONS

HC595 SHIFT REGISTER

Wide Supply Voltage Range from 2.0V to 6.0V
Sinks or sources 8mA at VCC = 4.5V
CMOS low power consumption
Schmitt Trigger Action at All Inputs
Inputs accept up to 6.0V
ESD Protection Tested per JESD 22

PIN DESCRIPTION

HC595 SHIFT REGISTER

10K POTENTIOMETER

LED

CIRCUIT DESCRIPTION

Make the circuit (see above) and connect the first shift register as following:

-GND (pin 8) to ground

-Vcc (pin 16) to 5V

-OE (pin 13) to ground

-MR (pin 10) to 5V

-DS (pin 14) to Arduino pin 11

-SH_CP (pin 11) to Arduino pin 12

-ST_CP (pin 12) to Arduino pin 8

Connect the second shift register exactly the same, but connect the DS (pin 14) to first register pin 9. After that connect pins: 1, 2, 3, 4, 5, 6, 7 and15 from both registers to LEDs. This connection makes all the pins always active and addressable, however when the Arduino is powered up some of the LEDs may be turned on. Solution for this is to connect MR (pin 10) and OE (pin 13) to Arduino directly, but it this way you have to sacrifice 2 Arduino pins.
To add more shift registers connect them like the second register. Always connect MR and OE pins directly to Arduino and DS pin to previous register
If you want to regulate the brightness of LEDs then connect potentiometer as shown in picture above to control resistance for all LEDs. However it is optional and you can get along without it.

CODE

Click to see the code and copy the link:

https://docs.google.com/document/d/e/2PACX-1vSAV7RlsqVdEBp7nkC2yc2gDA_H6_Fra6cPe3fRFmJ-IDiHFyBEOR4Yz9ETlkZ-k1pzg7PyevKDBa6D/pub

WORKING

Connect the Arduino uno and upload the Code given next .After uploading the code you will see the different pattern by glowing led which is controlled by potentiometer.

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Related products

UNO R3 Board Starter Kit 30+ DIY Projects Video tutorials

Add to cart

Arduino Compatible Kits

UNO R3 Board Starter Kit 30+ DIY Projects Video tutorials

-40%

Super Starter Kit for Uno R3 compatible with Arduino IDE

Add to cart

Arduino Compatible Kits

Super Starter Kit for Uno R3 compatible with Arduino IDE

-35%

ARDUIN0 SMD Uno Based Super Starter Kit smd Full Learning Kit

Add to cart

Arduino Compatible Kits

ARDUIN0 SMD Uno Based Super Starter Kit smd Full Learning Kit

-5%

Basic Starter Kit For Compatible With Arduino SMD UN

Add to cart

Arduino Compatible Kits

Basic Starter Kit For Compatible With Arduino SMD UN

-10%

2Wd Transparent Smart Motor Robot Car Chassis Kit with Arduino Board

Add to cart

Arduino Compatible Kits

2Wd Transparent Smart Motor Robot Car Chassis Kit with Arduino Board

-16%

Make A Line Follower Robot Using L293D Motor Driver Module Interfacing With Arduino Uno-

Add to cart

Arduino Compatible Kits

Make A Line Follower Robot Using L293D Motor Driver Module Interfacing With Arduino Uno-

-9%

Blog

{"title":"All","number":"3","post_title":1,"ignore_sticky_posts":true,"meta":{"meta_date":true},"layout":"list","list_layout":"list_1","grid_layout":"grid_1","featured_layout":"featured_1","image_size":"hexwp_thumbnail","ratio":"hw-ratio100","image_width":"27","box_layout":"none","post_type":"post","action":"hexwp_post_list","post_status":"publish"}