Pin	Name	Description
1	GND	Ground (It grounds the Input and complete the circuit path)
2	VCC	3.3 V to 5 V (Recommended Voltage)
3	OUT	Output (It goes low when obstacle is in range)
4	EN	Enable (It enables the circuit)as an activation sensor PIN (putting it in HIGH) and deactivating the sensor (putting it on LOW)

IMPORTANT:

This sensor allows you to activate and deactivate the obstacle detection by manipulating the enable-pin.
It is activated by default which means that the sensor is in detection mode by default.
If you don’t want that, you need to remove the jumper with the label “EN” and put a control signal on the enable pin.

CIRCUIT CONNECTION

An LED is attached to pin 13 of the Arduino Uno board to build a simple circuit of Obstacle Avoidance Sensor Module.
With the LED attached to pin 13, connect pin OUT of Obstacle Avoidance Sensor to D8 of the Arduino Uno board for displaying the Output. The Output pin goes LOW, when obstacle is within range due to reduced resistance of the photodiode (component in Obstacle Avoidance Sensor).
When the sensor detects an obstacle then the LED is turned ON automatically or else it stays off.
The EN (Enable) pin is used to enable the circuit. The Pin EN is an activation sensor PIN (putting it in HIGH) and deactivating the sensor (putting it on LOW), but the result will be the same. When reading, the input is always 1. But is not used in the given circuit connection.

CODE

Click to see the code: https://docs.google.com/document/d/e/2PACX-1vT7bfujCSt-KnHGZmlAeqLCPp5UKSLzraCknebYG35VehDUak4sbs7W4kVZOsoweoo1YaQZH749MOlp/pub?embedded=true

WORKING

This Arduino based Obstacle Avoidance Sensor mainly consists of an infrared-transmitter, an infrared-receiver and a potentiometer. In this particular sensor module, we identify the obstacle through the use of LED which is connected to Pin 13 of Arduino Uno board. Later, when the sensor detects an obstacle it turns ON the LED and further Output is being displayed on Serial Monitor.

Its working principle depends upon the reflecting character of an object. When the light emitted by the IR LED is incident on the photodiode after hitting an object, the resistance of the photodiode falls down from a huge value. One of the input of the op – amp is at threshold value set by the potentiometer. The other input to the op-amp is from the photodiode’s series resistor. When the incident radiation is more on the photodiode, the voltage drop across the series resistor will be high. In the IC, both the threshold voltage and the voltage across the series resistor are compared. If the voltage across the resistor series to photodiode is greater than that of the threshold voltage, the output of the IC Op – Amp is high. As the output of the IC is connected to an LED, it lightens up.

Battery operated	yes,1 nos 9V battery included

Reviews

There are no reviews yet.

Be the first to review “How to Identify Obstacles Using Obstacle Avoidance Sensor by Interfacing with Arduino Uno”

You must be logged in to post a review.

Turn on and off Led using Tracking Sensor Module

-13%

Move Robotic Head using Obstacle avoiding Module

Add to cart

Arduino Compatible Kits

Move Robotic Head using Obstacle avoiding Module

-3%

Related products

Crowtail-Deluxe Kit for Arduino with 20 Module Sensors for Educational Learners

Out of Stock

Arduino Compatible Kits

Crowtail-Deluxe Kit for Arduino with 20 Module Sensors for Educational Learners

-15%

ARDUIN0 SMD Uno Based Super Starter Kit smd Full Learning Kit

Add to cart

Arduino Compatible Kits

ARDUIN0 SMD Uno Based Super Starter Kit smd Full Learning Kit

-5%

Make a Gesture Based TV Remote Control Using Ultrasonic Sensor and IR Transmitter with Arduino Uno

Add to cart

Arduino Compatible Kits

Make a Gesture Based TV Remote Control Using Ultrasonic Sensor and IR Transmitter with Arduino Uno

-10%

Add to cart

Arduino Compatible Kits

Project Basic R3 Starter Kit compatible

-25%

Ultimate Uno R3 Kit compatible with ARDUIN0 IDE

Add to cart

Arduino Compatible Kits

Ultimate Uno R3 Kit compatible with ARDUIN0 IDE

-11%

DIY Ultrasonic Distance Sensor Starter Kit For Compatible with Smd UNO IDE Projects

Add to cart

Arduino Compatible Kits

DIY Ultrasonic Distance Sensor Starter Kit For Compatible with Smd UNO IDE Projects

-4%

Blog

{"title":"All","number":"3","post_title":1,"ignore_sticky_posts":true,"meta":{"meta_date":true},"layout":"list","list_layout":"list_1","grid_layout":"grid_1","featured_layout":"featured_1","image_size":"hexwp_thumbnail","ratio":"hw-ratio100","image_width":"27","box_layout":"none","post_type":"post","action":"hexwp_post_list","post_status":"publish"}

How to Build a Robot Car at Home (Step-by-Step Guide for Beginners 2026)

April 15, 2026

Top 10 Arduino Projects for Beginners (Step-by-Step Guide 2026)

April 15, 2026

Best Robotics Kits for Beginners in India (2026 Guide)

April 15, 2026

You may also like…

Turn on and off Led using Tracking Sensor Module

Move Robotic Head using Obstacle avoiding Module

Related products

Crowtail-Deluxe Kit for Arduino with 20 Module Sensors for Educational Learners

ARDUIN0 SMD Uno Based Super Starter Kit smd Full Learning Kit

Make a Gesture Based TV Remote Control Using Ultrasonic Sensor and IR Transmitter with Arduino Uno

Project Basic R3 Starter Kit compatible

Ultimate Uno R3 Kit compatible with ARDUIN0 IDE

DIY Ultrasonic Distance Sensor Starter Kit For Compatible with Smd UNO IDE Projects

How to Build a Robot Car at Home (Step-by-Step Guide for Beginners 2026)

Top 10 Arduino Projects for Beginners (Step-by-Step Guide 2026)

Best Robotics Kits for Beginners in India (2026 Guide)

Categories

My Account

Information